ANNEXURE
– I B
SPECIFICATIONS
OF CONSUMER PACKS
A Flexible Pouches : ( 500 grams, 1 kg and 2
kg )
Material of Pouch
: Laminate of polyester/LDPE
LDPE -
50 micron
The material
shall be either extrusion laminated, or in the case of adhesive lamination,
food grade, odour free adhesive should be used.
Type of Pouch : a) Pillow Pouch or
b) Side
gusseted pouch
Dimensions of pouch :
As indicated in Annexure I – A.
Bond Strength : 250 gm /15 mm
(minimum)
Heat Seal Strength :
2kg / 15 mm ( minimum)
Seal width : 5 mm ( minimum
)
Note :
1 . While the
above is indicative type of laminate that is recommended, any other flexible
film or laminate comparable to the the barrier, strength and printing
properties and low temperature
stability of the above laminate would also be accepted.
2 . Tolerance
a) Permissiable lower level
Polyester film ( -5% ) (minus 5
percent )
Polyethylene film ( -10 % ) (
minus 10 percent )
b) Upper Level
A
higher specification ( positive tolerance ) always could be
acceptable, but however should not lead to high rigidity, flex
crack,,reduced bond strength or seal strength. A higher
specification may add to the cost.
3. The laminate
material could be transparent/opaque/coloured as per the
requirements of
the importer.
4.. All the materials used shall be of food grade and pass
the prescribed
Indian
standard/standards if any and as demanded by the importing
countries.
5.
Printing
requirements shall conform to as prescribed by the importing
countries.
6. General
observations :
a)
The pouches shall
be clean and without any specs.
b)
The pouches shall
be 3 sides or 4 sides sealed, or gusseted.
c)
The seal width
shall be minimum 5 mm, particularly the top seal (for filled pouches ).
d)
The pouches shall
be either reverse or surface printed. In the case of surface print, the print
shall be compatible with the product and shall not lift or smudge. The print
shall be legible and easy to read.
B. Plastic
Punnet ( 500 grams )
Material : Food grade, odourless PET
( polyethylene terephthalate)
Design : As per drawings no.3
Dimensions : As indicated in
Annexure – I A.
Approx. Wt.(gms) :
25.00
Note : The lid should sit firmly on the tray and
should be lockable type.
ANNEXURE – II C1
SPECIFICATION DETAILS
OF TRANSPORT PACK
Product : Precut frozen fruits and vegetables .
Type
of Consumer Pack : a) Flexible Pillow
Pouch.
b)
Flexible gusseted pouch
Capacity
of Consumer Pack : 500
grams., 1 kg., 2 kg.
Material of Construction : 3 - ply
corrugated fibre board*
External Dimensions (mm) :
a) 400 x 300 x 315 b) 500 x 400 x
200
Style
of Box : a) RSC (0201) b) Telescopic
(0312)
Type of Flutes
: ‘B’/narrow
Direction of Flutes : Vertical
Grammage (g/m2 )
: 190 / 150 /190.
(outer to innner ) ( indicative )
Burst Factor of Kraft Paper : Min 25
Bursting Strength of Board ( kg/cm2
) : Min 15
No. of
pieces per Box
: Not more than two
Manufacturer’s Joint : By gluing
Compression Strength of box (kgf)
: Min 300
Cobb (30 minutes) (g/m2)
: Max. 60
*
Outer ply with waterproof coating or
plastic film lamination.
Note : Dimensions of the box are modular
to Euro pallets. However, any
other dimensions or box styles to
suit importers requirements could
also be used.
ANNEXURE – II – C2
SPECIFICATION DETAILS
OF TRANSPORT PACK.
Product :
Precut frozen fruits and vegetables
.
Type
of Consumer Pack :
Plastic Punnet with Lid
Capacity
of Consumer Pack :
500 grams.
Material of Construction : 3
- ply corrugated fibre board *
External Dimensions (mm) : 500 x 300 x 200
Style of Box :
a) RSC 0201 b) Telescopic
0312
Type of Flutes :
‘B’/narrow
Direction of Flutes : Vertical
Grammage (g/m2) : 190 / 150 /190.
(outer to innner ) (indicative )
Burst Factor of Kraft Paper : Min 25
Bursting Strength of Board (kg/cm2) :
Min 15.0
No. of
Pieces per box :
Not more than two
Manufacturers Joint : By gluing.
Compression Strength (kgf) : Min
300
Cobb (30 minutes) (g/m2) :
Max. 60
* Outer ply with water proof coating or plastic film lamination.
Note : Dimensions of the box are modular
to Euro pallets. However, any
other dimensions or box styles to
suit importers requirements could
also be used.
ANNEXURE –
II D
SPECIFICATION DETAILS
FOR PRESSURE SENSITIVE TAPE AND REINFORCEMENT STRAP
a) Pressure sensitive Tape
Material : BOPP or PVC
(
biaxially oriented Polypropylene )
or
( Polyvinyl Chloride )
Width : 50 mm ( minimum )
Adhesion Property :
To pass as per IS : 3676 – 1986
( For further
specification details refer IS : 2880 –
1987 )
b) Reinforcement Strap
Material :
PP or HDPE
(Polypropylene or
high density polyethylene)
Width : 12mm (minimum )
Thickness : 0.50 mm ( minimum )
Breaking
Load : 80 kg / 12 mm width
Elongation :
25 % ( maximum )
ANNEXURE
– III A
SPECIFICATION DETAILS FOR DIRECT BULK PACK
PRODUCT :
Okra / Beans / Bitter gourd / Acid lime
CAPACITY :
10 kg.
1)
MATERIAL OF CONSTRUCTION : Corrugated fibre board *
2) EXTERNAL DIMENSIONS (MM) : 500 x 300 x 200
3) STYLE OF BOX : RSC
(0201) **
4) TYPE OF FLUTES : B/B
5) DIRECTION OF FLUTES : Vertical
6) NO. OF PLIES : 5
7) GRAMMAGE (G/ M.SQ.)
(OUTER TO INNER) : 250/120/120/120/120
8) BURST FACTOR OF PAPER
(KRAFT)
: 20.00
9) BURSTING STRENGTH OF
BOARD (KG/CM.SQ.) : 14.00
10) NO. OF PIECES PER BOX : Not more than two
11) MANUFACTURER’S JOINT : By gluing
12) COMPRESSION STRENGTH
OF BOX (KGF) : 400.00
13) COBB (30 MINUTES)
(G/M.SQ.) (MAX.) :
60.00
14) NO. OF VENTILATION
HOLES : 16.00
15) DIAMETER AND POSITION : 20 mm. 3 holes each
on the two sides.
OF HOLES 1 hole
each on the two ends.
4 holes
each on top & bottom.
* Outer ply of White duplex
board
** Or any other suitable style
which provides equal strength and performance
ANNEXURE
– III B
SPECIFICATION DETAILS FOR DIRECT BULK PACK
PRODUCT :
Okra / Beans / Bitter gourd / Acid lime
CAPACITY :
10 kg.
1)
MATERIAL OF CONSTRUCTION : Corrugated fibre board *
2) EXTERNAL DIMENSIONS (MM) : 500 x 300 x 200
3) STYLE OF BOX : Telescopic (0300) **
4) TYPE OF FLUTES : Lid / Tray : B(narrow)
5) DIRECTION OF FLUTES : Vertical
6) NO. OF PLIES : 3
7) GRAMMAGE (G/ M.SQ.)
(OUTER TO INNER) : Lid / Tray
: 250/150/150
8) BURST FACTOR OF PAPER
(KRAFT)
: 20.00
9) BURSTING STRENGTH OF
BOARD (KG/CM.SQ.) : Lid / Tray : 11.00
10) NO. OF PIECES PER BOX : Not more than two
11) MANUFACTURER’S JOINT : By gluing
12) COMPRESSION STRENGTH
OF BOX (KGF) (MIN) : 400.00
13) COBB (30 MINUTES)
(G/M.SQ.) (MAX.) :
60.00
14) NO. OF VENTILATION
HOLES : 16.00
15) DIAMETER AND POSITION :
3 holes each on the two sides.
OF HOLES 1 hole each on the two
ends.
4 holes each on top & bottom.
* Outer ply of White duplex
board
** Or any other suitable
style which
provides equal strength
and performance
ANNEXURE
– III C
SPECIFICATION DETAILS FOR DIRECT BULK PACK
PRODUCT :
Okra / Beans / Bitter gourd / Acid lime
CAPACITY :
10 kg.
1)
MATERIAL OF CONSTRUCTION : Corrugated fibre board *
2) EXTERNAL DIMENSIONS (MM) : 500 x 300 x 200
3) STYLE OF BOX : Telescopic (0306) **
4) TYPE OF FLUTES : Lid / Tray : B(narrow)
5) DIRECTION OF FLUTES : Vertical
6) NO. OF PLIES :
3
7) GRAMMAGE (G/ M.SQ.)
(OUTER TO INNER) : Lid / Tray
: 250/150/150
8) BURST FACTOR OF PAPER
(KRAFT) :
20.00
9) BURSTING STRENGTH OF
BOARD (KG/CM.SQ.) : Lid / Tray : 11
10) NO. OF PIECES PER BOX : Not more than two
11) MANUFACTURER’S JOINT : By gluing
12) COMPRESSION STRENGTH
OF BOX (KGF) (MIN) :
400.00
13) COBB (30 MINUTES)
(G/M.SQ.) (MAX.) :
60.00
14) NO. OF VENTILATION
HOLES : 16.00
15) DIAMETER AND POSITION : 20 mm. 3 holes each on the two sides.
OF HOLES 1 hole
each on the two ends.
4 holes each on the top & bottom.
* Outer ply of White duplex
board
** Or any other suitable style
which
provides equal strength
and performance
ANNEXURE
- III D
SPECIFICATION DETAILS FOR DIRECT BULK PACKS
PRODUCT :
Okra / Beans / Bitter gourd / Acid lime
CAPACITY :
10 kg.
1)
MATERIAL OF CONSTRUCTION : Corrugated fibre board *
2) EXTERNAL DIMENSIONS (MM) : 500 x 300 x 200
3) STYLE OF BOX : Telescopic
(0312) **
4) TYPE OF FLUTES : Lid : B(narrow), Tray : B/B (narrow)
5) DIRECTION OF FLUTES : Vertical
6) NO. OF PLIES : Lid / Tray : 3/5
7) GRAMMAGE (G/ M.SQ.) : Lid : 250/150/150
(OUTER TO INNER) Tray :
250/120/120/120/120
8) BURST FACTOR OF PAPER
(KRAFT)
: 20.00
9) BURSTING STRENGTH OF
BOARD (KG/CM.SQ.) : Lid / Tray : 11/ 14
10) NO. OF PIECES PER BOX : Not more than two
11) MANUFACTURER’S JOINT : By gluing
12) COMPRESSION STRENGTH
OF BOX (KGF) (MIN) :
400.00
13) COBB (30 MINUTES)
(G/M.SQ.) (MAX.) : 60.00
14) NO. OF VENTILATION
HOLES : 16.00
15) DIAMETER AND POSITION : 20 mm. 3 holes each
on the two sides.
OF HOLES 1 hole
each on the two ends.
4 holes each on the top & bottom.
* Outer ply of White duplex
board
** Or any other suitable style
which
provides equal strength
and performance
ANNEXURE
– III E
SPECIFICATION DETAILS FOR DIRECT BULK PACKS
PRODUCT :
Okra / Beans / Bitter gourd / Papaya / Pineapple
CAPACITY :
5 - 7 kg.
1)
MATERIAL OF CONSTRUCTION : Corrugated fibre board *
2) EXTERNAL DIMENSIONS (MM) : 400 x 300 x 200
3) STYLE OF BOX : RSC (0201) **
4) TYPE OF FLUTES : B (narrow)
5) DIRECTION OF FLUTES : Vertical
6) NO. OF PLIES : 3
7) GRAMMAGE (G/ M.SQ.)
(OUTER TO INNER) : 250/150/150
8) BURST FACTOR OF PAPER
(KRAFT) :
20.00
9) BURSTING STRENGTH OF
BOARD (KG/CM.SQ.) : 11.00
10) NO. OF PIECES PER BOX : Not more than two
11) MANUFACTURER’S JOINT : By gluing
12) COMPRESSION STRENGTH
OF BOX (KGF) (MIN) :
350.00
13) COBB (30 MINUTES)
(G/M.SQ.) (MAX.) :
60.00
14) NO. OF VENTILATION
HOLES : 14.00
15) DIAMETER AND POSITION : 20 mm. 2 holes each
on the two sides.
OF HOLES 1 hole
each on the two ends.
4 holes each on the top & bottom.
* Outer ply of White duplex
board.
** Or any other suitable style
which
provides equal strength and
performance.
ANNEXURE
– III F
SPECIFICATION DETAILS FOR DIRECT BULK PACKS
PRODUCT :
Okra / Beans / Bitter gourd / Papaya / Pineapple
CAPACITY :
5 - 7 kg.
1)
MATERIAL OF CONSTRUCTION : Corrugated fibre board *
2) EXTERNAL DIMENSIONS (MM) : 400 x 300 x 200
3) STYLE OF BOX : Telescopic
(0300) **
4) TYPE OF FLUTES :
Lid/Tray : B (narrow)
5) DIRECTION OF FLUTES : Vertical
6) NO. OF PLIES : 3
7) GRAMMAGE (G/ M.SQ.)
(OUTER TO INNER) : Lid / Tray
: 250/150/150
8) BURST FACTOR OF PAPER
(KRAFT)
: 20.00
9) BURSTING STRENGTH OF
BOARD (KG/CM.SQ.) : Lid/Tray :
11/ 11
10) NO. OF PIECES PER BOX : Not more than two
11) MANUFACTURER’S JOINT : By gluing
12) COMPRESSION STRENGTH
OF BOX (KGF) (MIN)
: 350.00
13) COBB (30 MINUTES)
(G/M.SQ.) (MAX.) :
60.00
14) NO. OF VENTILATION
HOLES : 14.00
15) DIAMETER AND POSITION : 20 mm. 2 holes each
on two sides.
OF HOLES 1 hole
each on two ends.
4 holes each on top & bottom.
* Outer ply of White duplex
board
** Or any other suitable
style which
provides equal strength
and performance
ANNEXURE
– III G
SPECIFICATION DETAILS FOR DIRECT BULK PACKS
PRODUCT :
Okra / Beans / Bitter gourd / Papaya / Pineapple
CAPACITY :
5 - 7 kg.
1)
MATERIAL OF CONSTRUCTION : Corrugated fibre board *
2) EXTERNAL DIMENSIONS (MM) : 400 x 300 x 200
3) STYLE OF BOX : Telescopic
(0306) **
4) TYPE OF FLUTES : Lid/Tray :
B (narrow)
5) DIRECTION OF FLUTES : Vertical
6) NO. OF PLIES : 3
7) GRAMMAGE (G/ M.SQ.)
(OUTER TO INNER) : Lid /
Tray : 250/150/150
8) BURST FACTOR OF PAPER
(KRAFT)
: 20.00
9) BURSTING STRENGTH OF
BOARD (KG/CM.SQ.) : Lid/Tray :
11/ 11
10) NO. OF PIECES PER BOX : Not more than two
11) MANUFACTURER’S JOINT : By gluing
12) COMPRESSION STRENGTH
OF BOX (KGF) (MIN) :
350.00
13) COBB (30 MINUTES)
(G/M.SQ.) (MAX.) : 60.00
14) NO. OF VENTILATION
HOLES : 14.00
15) DIAMETER AND POSITION : 20 mm. 2 holes each
on the two sides.
OF HOLES 1 hole
each on the two ends.
4 holes each on top & bottom.
* Outer ply of White duplex
board
** Or any other suitable style
which
provides equal strength
and performance
SPECIFICATION DETAILS FOR DIRECT BULK PACKS
PRODUCT :
Okra / Beans / Bitter gourd / Papaya / Pineapple
CAPACITY :
5 - 7 kg.
1)
MATERIAL OF CONSTRUCTION : Corrugated fibre board *
2) EXTERNAL DIMENSIONS (MM) : 400 x 300 x 200
3) STYLE OF BOX : Telescopic (0312) **
4) TYPE OF FLUTES : Lid/Tray :
B (narrow)
5) DIRECTION OF FLUTES : Vertical
6) NO. OF PLIES : 3
7) GRAMMAGE (G/ M.SQ.)
(OUTER TO INNER) : Lid / Tray
: 250/150/150
8) BURST FACTOR OF PAPER
(KRAFT)
: 20.00
9) BURSTING STRENGTH OF
BOARD (KG/CM.SQ.) : Lid/Tray :
11.00
10) NO. OF PIECES PER BOX : Not more than two
11) MANUFACTURER’S JOINT : By gluing
12) COMPRESSION STRENGTH
OF BOX (KGF) (MIN) :
350.00
13) COBB (30 MINUTES)
(G/M.SQ.) (MAX.) :
60.00
14) NO. OF VENTILATION
HOLES : 14.00
15) DIAMETER AND POSITION : 20 mm. 2 holes each
on both the sides.
OF HOLES 1 hole
each on both the ends.
4 holes each on top
& bottom.
* Outer ply of White duplex board
** Or any other suitable style
which
provides equal strength
and performance
ANNEXURE - III I
SPECIFICATION DETAILS FOR DIRECT BULK PACKS
PRODUCT :
Bitter gourd / Cucumber/ Acid lime/ Chikoo
CAPACITY :
4 - 6 kg.
1)
MATERIAL OF CONSTRUCTION : Corrugated fibre board *
2) EXTERNAL DIMENSIONS (MM) : 400 x 200 x 150
3) STYLE OF BOX : RSC (0201)
**
4) TYPE OF FLUTES : B (narrow)
5) DIRECTION OF FLUTES : Vertical
6) NO. OF PLIES : 3
7) GRAMMAGE (G/ M.SQ.)
(OUTER TO INNER) : 250/150/150
8) BURST FACTOR OF PAPER
(KRAFT)
: 20.00
9) BURSTING STRENGTH OF
BOARD (KG/CM.SQ.) : 11.00
10) NO. OF PIECES PER BOX : Not more than two
11) MANUFACTURER’S JOINT : By gluing
12) COMPRESSION STRENGTH
OF BOX (KGF) (MIN) :
350.00
13) COBB (30 MINUTES)
(G/M.SQ.) (MAX.) :
60.00
14) NO. OF VENTILATION
HOLES : 10.00
15) DIAMETER AND POSITION : 20.00 mm. 2 holes
each on the two sides.
OF HOLES 1 hole
each on the two ends.
2 holes each on top & bottom.
* Outer ply of White duplex
board
** Or any other suitable style
which
provides equal strength and
performance.
ANNEXURE
– III J
SPECIFICATION DETAILS FOR DIRECT BULK PACKS
PRODUCT :
Bitter gourd / Cucumber/ Acid lime/ Chikoo
CAPACITY :
4 - 6 kg.
1)
MATERIAL OF CONSTRUCTION : Corrugated fibre board *
2) EXTERNAL DIMENSIONS (MM) : 400 x 200 x 150
3) STYLE OF BOX : Telescopic
(0300) **
4) TYPE OF FLUTES : Lid/Tray :
B (narrow)
5) DIRECTION OF FLUTES : Vertical
6) GRAMMAGE (G/ M.SQ.)
(OUTER TO INNER) : Lid/Tray :
250/150/150
7) BURST FACTOR OF PAPER
(KRAFT) : 20.00
8) BURSTING STRENGTH OF
BOARD (KG/CM.SQ.) : Lid /Tray:
11.00 / 11.00
9) NO. OF PIECES PER
BOX : Not more than two
10) MANUFACTURER’S JOINT : By gluing
11) COMPRESSION STRENGTH
OF BOX (KGF) (MIN) :
350.00
12) COBB (30 MINUTES)
(G/M.SQ.) (MAX.) :
60.00
13) NO. OF VENTILATION
HOLES : 10.00
14) DIAMETER AND POSITION : 20.00 mm. 2 holes each on the two sides.
OF HOLES 1
hole each on the two ends.
2 holes each on top &
bottom.
* Outer ply of White duplex
board
** Or any other suitable style
which
provides equal strength
and performance
ANNEXURE
– III K
SPECIFICATION DETAILS FOR DIRECT BULK PACKS
PRODUCT :
Bitter gourd / Cucumber/ Acid
lime/ Chikoo
CAPACITY :
4 - 6 kg.
1)
MATERIAL OF CONSTRUCTION : Corrugated fibre board *
2) EXTERNAL DIMENSIONS (MM) : 400 x 200 x 150
3) STYLE OF BOX : Telescopic
(0306) **
4) TYPE OF FLUTES : Lid/Tray :
B (narrow)
5) DIRECTION OF FLUTES : Vertical
6) NO. OF PLIES : 3
7) GRAMMAGE (G/ M.SQ.)
(OUTER TO INNER) : Lid/Tray :
250/150/150
8) BURST FACTOR OF PAPER
(KRAFT)
: 20.00
9) BURSTING STRENGTH OF
BOARD (KG/CM.SQ.) : Lid
/Tray: 11.00 / 11.00
10) NO. OF PIECES PER BOX : Not more than two
11) MANUFACTURER’S JOINT : By gluing
12) COMPRESSION STRENGTH
OF BOX (KGF) (MIN) :
350.00
13) COBB (30 MINUTES)
(G/M.SQ.) (MAX.) :
60.00
14) NO. OF VENTILATION
HOLES : 10.00
15) DIAMETER AND POSITION : 20.00 2 holes each
on the two sides.
OF HOLES 1 hole
each on the two ends.
2 holes each on top & bottom. ends.
* Outer ply of White duplex
board
** Or any other suitable style
which
provides equal strength
and performance
ANNEXURE -
III L
SPECIFICATION DETAILS FOR DIRECT BULK PACKS
PRODUCT :
Bitter gourd / Cucumber/ Acid lime/ Chikoo
CAPACITY :
4 - 6 kg.
1)
MATERIAL OF CONSTRUCTION : Corrugated fibre board *
2) EXTERNAL DIMENSIONS (MM) : 400 x 200 x 150
3) STYLE OF BOX : Telescopic
(0312) **
4) TYPE OF FLUTES : Lid/Tray :
B (narrow)
5) DIRECTION OF FLUTES :
Vertical
6) GRAMMAGE (G/ M.SQ.)
(OUTER TO INNER) : Lid/Tray :
250/150/150
7) BURST FACTOR OF PAPER
(KRAFT) :
20.00
8) BURSTING STRENGTH OF
BOARD (KG/CM.SQ.) : Lid /Tray:
11.00 / 11.00
9) NO. OF PIECES PER
BOX : Not more than two
10) MANUFACTURER’S JOINT : By gluing
11) COMPRESSION STRENGTH
OF BOX (KGF) (MIN) :
350.00
12) COBB (30 MINUTES)
(G/M.SQ.) (MAX.) :
60.00
13) NO. OF VENTILATION
HOLES : 10.00
14) DIAMETER AND POSITION : 20.00 mm.
OF HOLES 2
holes each on the two sides.
1 hole each on the two ends.
2 holes each on top &
bottom.
* Outer ply of White duplex
board
** Or any other suitable
style which
provides equal strength
and performance
ANNEXURE
– III M
SPECIFICATION DETAILS FOR DIRECT BULK PACKS
PRODUCT :
Okra / Beans / Bittergourd / Papaya
CAPACITY :
8 kg.
1)
MATERIAL OF CONSTRUCTION : Corrugated fibre board *
2) EXTERNAL DIMENSIONS (MM) : 500 x 300 x 150
3) STYLE OF BOX : RSC
(0201) **
4) TYPE OF FLUTES : B/B (narrow)
5) DIRECTION OF FLUTES : Vertical
6) NO. OF PLIES : 5
7) GRAMMAGE (G/ M.SQ.)
(OUTER TO INNER) : 250/120/120/120/120
8) BURST FACTOR OF PAPER
(KRAFT)
: 20.00
9) BURSTING STRENGTH OF
BOARD (KG/CM.SQ.) : 11.00
10) NO. OF PIECES PER BOX : Not more than two
11) MANUFACTURER’S JOINT : By gluing
12) COMPRESSION STRENGTH
OF BOX (KGF) (MIN) :
300.00
13) COBB (30 MINUTES)
(G/M.SQ.) (MAX.) :
60.00
14) NO. OF VENTILATION HOLES :
16.00
15) DIAMETER AND POSITION : 20.00 mm 3 holes
each on the two sides.
OF HOLES 1
hole each on the two ends.
4 holes each
on the top & bottom.
* Outer ply of White duplex
board
** Or any other suitable style
which
provides equal strength
and performance
ANNEXURE
- III
N
SPECIFICATION DETAILS OF DIRECT BULK PACKS
CAPACITY :
8 kg.
1)
MATERIAL OF CONSTRUCTION : Corrugated fibre board *
2) EXTERNAL DIMENSIONS
(MM) : 500 x 300 x 150
3) STYLE OF BOX : Telescopic (0300) **
4) TYPE OF FLUTES : Lid/Tray : B (narrow)
5) DIRECTION OF FLUTES : Vertical
6) NO. OF PLIES : 3
7) GRAMMAGE (G/ M.SQ.)
(OUTER TO INNER) : Lid/Tray : 250/150/150
8) BURST FACTOR OF PAPER
(KRAFT)
: 20.00
9) BURSTING STRENGTH OF
BOARD (KG/CM.SQ.) : Lid/Tray : 11
10) NO. OF PIECES PER BOX : Not more than two
11) MANUFACTURER’S JOINT : By gluing
12) COMPRESSION STRENGTH
OF BOX (KGF) (MIN)
: 300.00
13) COBB (30 MINUTES)
(G/M.SQ.) (MAX.) :
60.00
14) NO. OF VENTILATION
HOLES : 16.00
15) DIAMETER AND POSITION : 20.00 mm 3 holes
each on the two sides.
OF HOLES 1
hole each on the two ends.
* Outer ply of White duplex
board
** Or any other suitable
style which
provides equal strength
and performance
ANNEXURE
– III O
SPECIFICATION DETAILS OF DIRECT BULK PACKS
PRODUCT :
Okra / Beans / Bittergourd / Papaya
CAPACITY
: 8 kg.
1)
MATERIAL OF CONSTRUCTION : Corrugated fibre board *
2) EXTERNAL DIMENSIONS (MM) : 500 x 300 x 150
3) STYLE OF BOX : Telescopic
(0306) **
4) TYPE OF FLUTES : Lid/Tray : B (narrow)
5) DIRECTION OF FLUTES : Vertical
6) NO. OF PLIES : 3
7) GRAMMAGE (G/ M.SQ.)
(OUTER TO INNER) : Lid/Tray : 250/150/150
8) BURST FACTOR OF PAPER
(KRAFT)
: 20.00
9) BURSTING STRENGTH OF
BOARD (KG/CM.SQ.) : Lid/Tray : 11/11
10) NO. OF PIECES PER BOX : Not more than two
11) MANUFACTURER’S JOINT : By gluing
12) COMPRESSION STRENGTH
OF BOX (KGF) (MIN) :
300.00
13) COBB (30 MINUTES)
(G/M.SQ.) (MAX.) :
60.00
14) NO. OF VENTILATION
HOLES : 16.00
15) DIAMETER AND POSITION : 20.00 mm 3 holes
each on the two sides.
OF HOLES 1
hole each on the two ends.
4 holes
each on the top & bottom
* Outer ply of White duplex
board
** Or any other suitable style
which
provides equal strength
and performance
ANNEXURE
– III P
SPECIFICATION DETAILS FOR DIRECT BULK PACKS
PRODUCT :
Okra / Beans / Bittergourd / Papaya
CAPACITY :
8 kg.
1)
MATERIAL OF CONSTRUCTION : Corrugated fibre board *
2) EXTERNAL DIMENSIONS (MM) : 500 x 300 x 150
3) STYLE OF BOX :
Telescopic (0312) **
4) TYPE OF FLUTES : Lid/Tray : B/B (narrow)
5) DIRECTION OF FLUTES :
6) NO. OF PLIES : Lid/Tray:
3/5
7) GRAMMAGE (G/ M.SQ.) : Lid : 250/150/150
(OUTER TO INNER) Tray : 250/120/120/120/120
8) BURST FACTOR OF PAPER
(KRAFT)
: 20.00
9) BURSTING STRENGTH OF
BOARD (KG/CM.SQ.) : Lid/Tray : 11/14
10) NO. OF PIECES PER BOX : Not more than two
11) MANUFACTURER’S JOINT : By gluing
12) COMPRESSION STRENGTH
OF BOX (KGF) (MIN) :
300.00
13) COBB (30 MINUTES)
(G/M.SQ.) (MAX.) :
60.00
14) NO. OF VENTILATION
HOLES : 16.00
15) DIAMETER AND POSITION : 20.00 mm 3 holes
each on the two sides.
OF HOLES 1 hole each on the
two ends.
4 holes each on top & bottom.
* Outer ply of White duplex
board
** Or any other suitable style
which
provides equal strength
and performance
ANNEXURE -
III Q
SPECIFICATION DETAILS OF DIRECT BULK PACKS
PRODUCT :
Pomegranate
CAPACITY :
5 kg. (approx. 12 nos.)
1)
MATERIAL OF CONSTRUCTION : Corrugated fibre board *
2) EXTERNAL DIMENSIONS (MM) : 400 x 200 x 105
3) STYLE OF BOX : RSC
(0201) **
4) TYPE OF FLUTES : Lid/Tray : B (narrow)
5) DIRECTION OF FLUTES : Vertical
6) NO. OF PLIES : 3
7) GRAMMAGE (G/ M.SQ.)
(OUTER TO INNER) : Lid/Tray : 250/150/150
8) BURST FACTOR OF PAPER
(KRAFT)
: 20.00
9) BURSTING STRENGTH OF
BOARD (KG/CM.SQ.) : Lid/Tray : 11
10) NO. OF PIECES PER BOX : Not more than two
11) MANUFACTURER’S JOINT : By gluing
12) COMPRESSION STRENGTH
OF BOX (KGF) (MIN) :
250.00
13) COBB (30 MINUTES)
(G/M.SQ.) (MAX.) :
60.00
14) NO. OF VENTILATION
HOLES : 14.00
15) DIAMETER AND POSITION : 20.00 mm. 3 holes on
the two sides.
OF HOLES 1
hole on the two ends.
3 holes on top
& bottom.
* Outer ply of White duplex
board.
** Or any other suitable style
which
provides equal strength
and performance
ANNEXURE –
III R
SPECIFICATION DETAILS FOR DIRECT BULK PACKS
PRODUCT :
Pomegranate
CAPACITY :
5 kg. (approx. 12 nos.)
1)
MATERIAL OF CONSTRUCTION : Corrugated fibre board *
2) EXTERNAL DIMENSIONS (MM) : 400 x 200 x 105
3) STYLE OF BOX : Telescopic
(0300) **
4) TYPE OF FLUTES : Lid/Tray : B (Narrow)
5) DIRECTION OF FLUTES : Vertical
6) NO. OF PLIES : 3
7) GRAMMAGE (G/ M.SQ.)
(OUTER TO INNER) : Lid/Tray : 250/150/150
8) BURST FACTOR OF PAPER
(KRAFT)
: 20.00
9) BURSTING STRENGTH OF
BOARD (KG/CM.SQ.) : Lid/Tray : 11
10) NO. OF PIECES PER BOX : Not more than two
11) MANUFACTURER’S JOINT : By gluing
12) COMPRESSION STRENGTH
OF BOX (KGF) (MIN) :
250.00
13) COBB (30 MINUTES)
(G/M.SQ.) (MAX.) :
60.00
14) NO. OF VENTILATION
HOLES : 14.00
15) DIAMETER AND POSITION : 20.00 mm 3 holes each
on the two sides.
OF HOLES 1 hole each on the
two ends.
3 holes each on the top & bottom.
* Outer ply of White duplex
board
** Or any other suitable style
which
provides equal strength
and performance
:
ANNEXURE -
III S
SPECIFICATION DETAILS FOR DIRECT BULK PACKS
PRODUCT :
Pomegranate
CAPACITY :
5 kg. (approx. 12 nos.)
1)
MATERIAL OF CONSTRUCTION : Corrugated fibre board *
2) EXTERNAL DIMENSIONS (MM) : 400 x 200 x 105
3) STYLE OF BOX :
Telescopic (0306) **
4) TYPE OF FLUTES : Lid/Tray : B
5) DIRECTION OF FLUTES : Vertical
6) NO. OF PLIES : 3
7) GRAMMAGE (G/ M.SQ.)
(OUTER TO INNER) : Lid/Tray : 250/150/150
8) BURST FACTOR OF PAPER
(KRAFT)
: 20.00
9) BURSTING STRENGTH OF
BOARD (KG/CM.SQ.) : Lid/Tray : 11
10) NO. OF PIECES PER BOX : Not more
than two
11) MANUFACTURER’S JOINT : By gluing
12) COMPRESSION STRENGTH
OF BOX (KGF) (MIN) :
300.00
13) COBB (30 MINUTES)
(G/M.SQ.) (MAX.) : 60.00
14) NO. OF VENTILATION
HOLES : 14.00
15) DIAMETER AND POSITION : 20.00 mm 3 holes
each on the two sides.
OF HOLES 1
hole each on the two ends.
3 holes each on top & bottom.
* Outer ply of White duplex
board
** Or any other suitable
style which
provides equal strength
and performance
ANNEXURE -
III T
SPECIFICATION DETAILS FOR DIRECT BULK PACKS
PRODUCT :
Pomegranate
CAPACITY
: 5 kg. (approx. 12 nos.)
1)
MATERIAL OF CONSTRUCTION : Corrugated fibre board *
2) EXTERNAL DIMENSIONS (MM) : 400 x 200 x 105
3) STYLE OF BOX : Telescopic
(0312) **
4) TYPE OF FLUTES : Lid/Tray : B (narrow)
5) DIRECTION OF FLUTES : Vertical
6) NO. OF PLIES : 3
7) GRAMMAGE (G/ M.SQ.)
(OUTER TO INNER) : Lid/Tray : 250/150/150
8) BURST FACTOR OF PAPER
(KRAFT)
: 20.00
9) BURSTING STRENGTH OF
BOARD (KG/CM.SQ.) : Lid/Tray : 11
10) NO. OF PIECES PER BOX : Not more than two
11) MANUFACTURER’S JOINT : By gluing
12) COMPRESSION STRENGTH
OF BOX (KGF) (MIN) :
250.00
13) COBB (30 MINUTES)
(G/M.SQ.) (MAX.) :
60.00
14) NO. OF VENTILATION HOLES :
14.00
15) DIAMETER AND POSITION : 20.00 mm 3 holes on
the two sides.
1 hole on the two ends.
3 holes
each on top & bottom.
* Outer ply of White duplex
board
** Or any other suitable
style which
provides equal strength
and performance
ANNEXURE -
III U
SPECIFICATION
DETAILS FOR DIRECT BULK PACKS
PRODUCT :
Snakegourd
CAPACITY :
5 kg.
1)
MATERIAL OF CONSTRUCTION : Corrugated fibre board *
2) EXTERNAL DIMENSIONS (MM) : 400 x 200 x 120
3) STYLE OF BOX :
RSC (0201) **
4) TYPE OF FLUTES : B (Narrow)
5) DIRECTION OF FLUTES : Vertical
6) NO. OF PLIES : 3
7) GRAMMAGE (G/ M.SQ.)
(OUTER TO INNER) :
250/150/150
8) BURST FACTOR OF PAPER
(KRAFT)
: 20.00
9) BURSTING STRENGTH OF
BOARD (KG/CM.SQ.) : 11
10) NO. OF PIECES PER BOX : Not more than two
11) MANUFACTURER’S JOINT : By gluing
12) COMPRESSION STRENGTH
OF BOX (KGF) (MIN) :
250.00
13) COBB (30 MINUTES)
(G/M.SQ.) (MAX.) :
60.00
14) NO. OF VENTILATION
HOLES : 14.00
15) DIAMETER AND POSITION : 20.00 mm 3 holes
each on the two ends.
OF HOLES 4
holes each on top & bottom.
* Outer ply of White duplex
board
** Or any other suitable
style which
provides equal strength
and performance
ANNEXURE -
III V
SPECIFICATION DETAILS FOR DIRECT BULK PACKS
PRODUCT :
Drumstick
CAPACITY :
7 kg.
1)
MATERIAL OF CONSTRUCTION : Corrugated fibre board *
2) EXTERNAL DIMENSIONS (MM) : 600 x 250 x 135
3) STYLE OF BOX : RSC
(0201) **
4) TYPE OF FLUTES : B (Narrow)
5) DIRECTION OF FLUTES : Vertical
6) NO. OF PLIES : 3
7) GRAMMAGE (G/ M.SQ.)
(OUTER TO INNER) :
250/150/150
8) BURST FACTOR OF PAPER
(KRAFT)
: 20.00
9) BURSTING STRENGTH OF
BOARD (KG/CM.SQ.) : 11.00
10) NO. OF PIECES PER BOX : Not more than two
11) MANUFACTURER’S JOINT : By gluing
12) COMPRESSION STRENGTH
OF BOX (KGF) (MIN) :
300.00
13) COBB (30 MINUTES)
(G/M.SQ.) (MAX.) : 60.00
14) NO. OF VENTILATION
HOLES : 14.00
15) DIAMETER AND POSITION : 20.00 mm 3 holes
each on the two ends.
OF HOLES 4
holes each on the top & bottom.
* Outer ply of White duplex
board
** Or any other suitable
style which
provides equal strength
and performance
ANNEXURE -
III W
SPECIFICATION DETAILS FOR DIRECT BULK PACKS
PRODUCT :
Drumstick
CAPACITY :
5 kg.
1)
MATERIAL OF CONSTRUCTION : Corrugated fibre board *
2) EXTERNAL DIMENSIONS (MM) : 600 x 250 x 110
3) STYLE OF BOX : RSC
(0201) **
4) TYPE OF FLUTES :
B (Narrow)
5) DIRECTION OF FLUTES : Vertical
6) NO. OF PLIES : 3
7) GRAMMAGE (G/ M.SQ.)
(OUTER TO INNER) : 250/150/150
8) BURST FACTOR OF PAPER
(KRAFT)
: 20.00
9) BURSTING STRENGTH OF
BOARD (KG/CM.SQ.) : 11.00
10) NO. OF PIECES PER BOX : Not more than two
11) MANUFACTURER’S JOINT : By gluing
12) COMPRESSION STRENGTH
OF BOX (KGF) (MIN) :
250.00
13) COBB (30 MINUTES)
(G/M.SQ.) (MAX.) :
60.00
14) NO. OF VENTILATION
HOLES : 14.00
15) DIAMETER AND POSITION : 20.00 mm 3 holes
each on the two ends.
OF HOLES
4 holes each on top & bottom.
* Outer ply of White duplex board
** Or any other suitable style
which
provides equal strength
and performance
ANNEXURE -
III X
SPECIFICATION DETAILS FOR DIRECT BULK PACKS
PRODUCT :
Drumstick
CAPACITY :
10 kg.
1)
MATERIAL OF CONSTRUCTION : Corrugated fibre board *
2) EXTERNAL DIMENSIONS (MM) : 600 x 250 x 200
3) STYLE OF BOX : RSC
(0201) **
4) TYPE OF FLUTES : B/B
(narrow/narrow)
5) DIRECTION OF FLUTES : Vertical
6) NO. OF PLIES : 5
7) GRAMMAGE (G/ M.SQ.)
(OUTER TO INNER) : 250/120/120/120/120
8) BURST FACTOR OF PAPER
(KRAFT)
: 20.00
9) BURSTING STRENGTH OF
BOARD (KG/CM.SQ.) : 14.00
10) NO. OF PIECES PER BOX : Not more than two
11) MANUFACTURER’S JOINT : By gluing
12) COMPRESSION STRENGTH
OF BOX (KGF) (MIN) : 400.00
13) COBB (30 MINUTES)
(G/M.SQ.) (MAX.) :
60.00
14) NO. OF VENTILATION
HOLES : 16.00
15) DIAMETER AND POSITION : 20.00 mm 3 holes
each on the two ends.
OF HOLES 2
holes each on the two ends.
4 holes each on top & bottom.
* Outer ply of White duplex board
** Or any other suitable
style which
provides equal strength
and performance
ANNEXURE - IV
SPECIFICATION DETAILS FOR
PRESSURE SENSITIVE TAPE
AND
REINFORCEMENT STRAP
PRESSURE
SENSITIVE TAPE :
Material : BOPP or PVC
(Biaxally Oriented
Polypropylene )
OR
(Polyvinyl Chloride)
Width : 50 mm (minimum)
Adhesion Property :
To pass as per IS 3676-1986.
(For further specification
details refer IS 2880-1987)
REINFORCEMENT
STRAP :
Material : PP (Polypropylene)
Width : Min.
12 mm
Thickness : Min. 0.50 mm
Breaking Load :
80 kg / 12 mm width
Elongation : Max 25%
ANNEXURE V-A
SPECIFICATION DETAILS FOR DIRECT BULK PACK
PRODUCT :
Apples – Direct bulk (with slotted partitions)
CAPACITY :
Appx. 16 Kg. (80 nos.)
MATERIAL OF CONSTRUCTION
: * Corrugated Fibre board – 3
ply.
EXTERNAL DIMENSIONS (MM)
: 400 x 330 x 370
STYLE OF BOX : ** Telescopic - 0320
TYPE OF FLUTES :
B (narrow)
DIRECTION OF FLUTES
: Vertical
GRAMMAGE (G/M.SQ.)
OUTER TO INNER
(INDICATIVE) : 250/150/150
BURST FACTOR OF PAPER
(KRAFT) (MIN.) : 25
BURSTING STRENGTH OF
BOARD (KG/CM.SQ) (MIN.) : 12.0
NUMBER OF PIECES PER BOX
: Not more than two
MANUFACTURER’S JOINT : By gluing
COMPRESSION STRENGTH
OF BOX (KGF) (MIN.) : 500
COBB (30 MINUTES)
(G/M.SQ.) (MAX.) : 60
NO. OF VENTILATION HOLES,
: One slot on each of the ends
of the box,
DIAMETER AND POSITION OF
as shown in drawing no. 13
HOLES
* Outer ply of White duplex board.
** Or any other suitable style which provide
equal strength and
performance
ANNEXURE V-B
SPECIFICATION DETAILS FOR DIRECT BULK PACK
PRODUCT :
Apples – Direct bulk (with moulded pulp trays)
CAPACITY :
Appx. 16 kg. (80 nos.)
MATERIAL OF CONSTRUCTION
: * Corrugated Fibre board – 3
ply
EXTERNAL DIMENSIONS (MM)
: 520 x 315 x 300
STYLE OF BOX : ** Telescopic - 0320
TYPE OF FLUTES :
B (narrow)
DIRECTION OF FLUTES
: Vertical
GRAMMAGE (G/M.SQ.)
OUTER TO INNER
(INDICATIVE) : 250/150/150
BURST FACTOR OF PAPER
(KRAFT) (MIN.) : 25
BURSTING STRENGTH OF
BOARD (KG/CM.SQ) (MIN.) : 12.0
NUMBER OF PIECES PER BOX
: Not more than two.
MANUFACTURER’S JOINT : By gluing
COMPRESSION STRENGTH
OF BOX (KGF) (MIN.) : 500
COBB (30 MINUTES)
(G/M.SQ.) (MAX.) : 60
NO. OF VENTILATION HOLES,
: One slot on each of the ends
box,
DIAMETER AND POSITION OF
as shown in drawing no. 12.
HOLES
* Outer ply of White duplex
board.
** Or
any other suitable style which provide
equal strength and
performance
ANNEXURE
- VI
SPECIFICATION DETAILS FOR PARTITIONS & SEPARATOR
PLATES
DIRECT BULK PACK FOR
APPLES
MATERIAL OF CONSTRUCTION
: Corrugated Fibre board - 3
ply.
TYPE OF FLUTES : B (narrow)
DIRECTION OF FLUTES
FOR PARTITIONS :
Vertical
GRAMMAGE (G/M.SQ.)
OUTER TO INNER :
150/150/150
BURSTING STRENGTH OF
BOARD (KG/CM.SQ) (MIN.) : 6.50
ANNEXURE
- XII
SPECIFICATION
OF CONSUMER PACKS
A) Flexible Pouches : (250 grams, 500 grams)
Material of pouch :
LDPE or PP
Thickness (microns) :
37.5 or 25
Type of pouch : Pillow pouch
Seal width : 5 mm (minimum)
Note :
1) Tolerance
a)
Permissiable Lower Level
Polyethylene film (- 1.0%)
Polypropylene film (- 10%)
b)
Upper Level
A higher specification
(positive tolerance) always could be acceptable, but however should not lead to
high rigidity, flex crack or reduced seal strength. A higher specification may add to the cost.
2)
The material could be transparent/opaque coloured as per the
requirements of
the importer.
3)
The materials used shall be food grade and pass the prescribed Indian
Standard /
Standards if any, and as
demanded by the importing countries.
4)
Printing requirements shall conform to as prescribed by the importing
countries.
5) General Observations :
a) The pouches shall be clean and without any
foreign particle
b) The pouches shall be 3 sides or 4 sides
sealed or gusseted.
c) The seal width shall be minimum 5mm,
particularly the top seal
(for filled pouches)
d) The pouches shall be
either reverse or surface printed. In
the case of
surface print, the
print shall be compatible with the product and shall
not lift or
smudge. The print shall be legible and
easy to read.
B) Plastic Punnet :
(250 grams, 500 grams)
Material :
Food grade, odourless PET (Polyethylene Terepthalate)
Design : As per prototypes
Note : The lid should sit
firmly on the tray and should be lockable type.
C) Woven Net bag – String pull type
Material :
HDPE (High Density
Polyethylene)
OR
PA (Polyamide)
Weight
Per Mt. Sq. :
45 min.
D) Stretch film
Material :
Food grade, odourless, stretchable.
LDPE : (Low Density Polyethylene) film
OR
LLDPE :
(Linear Low Density Polyethylene) film
OR
PVC : (Polyvinyl Chloride) film
Thickness :
15.00
(micron)
F) EPS Tray
Material of :
(EPS) Expanded Polystyrene
Construction
Density g/cc :
0.08
ANNEXURE XV-A
TYPE OF CONSUMER
PACK : a)
Flexible Pouch b) Woven net bag
CAPACITY OF CONSUMER
PACK :
250 grams, 500 grams.
1)
MATERIAL OF CONSTRUCTION : 3
– ply Corrugated fibre board *
2) EXTERNAL DIMENSIONS (MM) : 500 x 400 x 140
3) STYLE OF BOX : a)
RSC (0201) b) Telescopic (0312)
4) TYPE OF FLUTES : B (Narrow)
5) DIRECTION OF FLUTES : Vertical
6) GRAMMAGE (G/ M.SQ.)
(OUTER TO INNER) : * 250/150/150
7) BURST FACTOR OF PAPER
(KRAFT)
: 20.00
8) BURSTING STRENGTH OF
BOARD (KG/CM.SQ.) : 11.00
9) NO. OF PIECES PER
BOX : Not more than two
10) MANUFACTURER’S JOINT : By gluing
11) COMPRESSION STRENGTH
OF BOX (KGF) (MIN) :
300.00
12) COBB (30 MINUTES)
(G/M.SQ.) (MAX.) :
60.00
13) NO. OF VENTILATION
HOLES : 16.00
14) DIAMETER AND POSITION : 20 mm - Drawing nos. 10
& 11.
OF HOLES 3 holes each on the two sides,
1 hole each on the two ends.
4 holes each on top & bottom.
* Outer ply of White duplex
board
Note : Dimensions of the box are
modular to Euro pallets. However, any
other
dimensions or box styles to suit importers requirement
could also be used.
ANNEXURE
XV-B
TYPE OF CONSUMER
PACK : a)
Plastic punnet with lid
b) Plastic punnet stretch wrapped
CAPACITY OF CONSUMER
PACK :
250 grams.
1)
MATERIAL OF CONSTRUCTION : 3 – ply
Corrugated fibre board *
2) EXTERNAL DIMENSIONS (MM) : 500 x 400 x 95
3) STYLE OF BOX : One piece tuck-in-type
4) TYPE OF FLUTES : B (Narrow)
5) DIRECTION OF FLUTES : Vertical
6) GRAMMAGE (G/ M.SQ.)
(OUTER TO INNER) : * 250/150/150
7) BURST FACTOR OF PAPER
(KRAFT)
: 20.00
8) BURSTING STRENGTH OF
BOARD (KG/CM.SQ.) : 11.00
9) NO. OF PIECES PER
BOX : One
10) MANUFACTURER’S JOINT : By gluing
11) COMPRESSION STRENGTH
OF BOX (KGF) (MIN) :
300.00
12) COBB (30 MINUTES)
(G/M.SQ.) (MAX.) :
60.00
13) NO. OF VENTILATION
HOLES : 19.00
14) DIAMETER AND POSITION : As shown in drawing nos. 12 & 13
OF HOLES
* Outer ply of White duplex
board
Note : Dimensions of the box are
modular to Euro pallets. However, any
other
dimensions or box
styles to suit importers requirement could also be used.
ANNEXURE XV-C
TYPE OF CONSUMER
PACK : a)
Plastic punnet with lid
b) Plastic punnet stretch
wrapped
CAPACITY OF CONSUMER
PACK :
500 grams.
1)
MATERIAL OF CONSTRUCTION : 3 – ply
Corrugated fibre board *
2) EXTERNAL DIMENSIONS (MM) : 500 x 400 x 135
3) STYLE OF BOX :
One piece tuck-in-type
4) TYPE OF FLUTES : B (Narrow)
5) DIRECTION OF FLUTES : Vertical
6) GRAMMAGE (G/ M.SQ.)
(OUTER TO INNER) : * 250/150/150
7) BURST FACTOR OF PAPER
(KRAFT)
: 20.00
8) BURSTING STRENGTH OF
BOARD (KG/CM.SQ.) : 11.00
9) NO. OF PIECES PER
BOX : One
10) MANUFACTURER’S JOINT : By gluing
11) COMPRESSION STRENGTH
OF BOX (KGF) (MIN) :
300.00
12) COBB (30 MINUTES)
(G/M.SQ.) (MAX.) :
60.00
13) NO. OF VENTILATION
HOLES : 19.00
14) DIAMETER AND POSITION : As shown in drawing nos. 12 & 13
OF HOLES
* Outer ply of White duplex
board
Note : Dimensions of the box are
modular to Euro pallets. However, any
other
dimensions or box
styles to suit importers requirement could also be used.
ANNEXURE XV-D
TYPE OF CONSUMER
PACK : a)
Plastic punnet with lid
b) Plastic punnet stretch wrapped
CAPACITY OF CONSUMER
PACK :
250 grams.
1)
MATERIAL OF CONSTRUCTION : 3 – ply
Corrugated fibre board *
2) EXTERNAL DIMENSIONS (MM) : 500 x 300 x 100
3) STYLE OF BOX : a) Telescopic (0306) b) Telescopic (0312)
4) TYPE OF FLUTES : B (Narrow)
5) DIRECTION OF FLUTES : Vertical
6) GRAMMAGE (G/ M.SQ.)
(OUTER TO INNER) : *
250/150/150
7) BURST FACTOR OF PAPER
(KRAFT)
: 20.00
8) BURSTING STRENGTH OF
BOARD (KG/CM.SQ.) : 11.00
9) NO. OF PIECES PER BOX : Not more than two
10) MANUFACTURER’S JOINT : By gluing
11) COMPRESSION STRENGTH
OF BOX (KGF) (MIN) :
300.00
12) COBB (30 MINUTES)
(G/M.SQ.) (MAX.) : 60.00
13) NO. OF VENTILATION
HOLES : 16.00
14) DIAMETER AND POSITION : 20 mm - drawing nos. 14 & 15
OF HOLES 3
holes each on the two sides
1
holes each on the two sides.
4 holes each on top and bottom.
* Outer ply of White duplex
board
Note : Dimensions of the box are
modular to Euro pallets. However, any
other
dimensions or box styles to suit importers
requirement could also be used.
ANNEXURE XV-E
TYPE OF CONSUMER
PACK : EPS tray
stretch wrapped
CAPACITY OF CONSUMER
PACK :
400 grams.
1)
MATERIAL OF CONSTRUCTION : 3 ply Corrugated fibre board *
2) EXTERNAL DIMENSIONS (MM) : 500 x 300 x 100
3) STYLE OF BOX : a) Telescopic (0306) b) Telescopic (0312)
4) TYPE OF FLUTES : B (Narrow)
5) DIRECTION OF FLUTES : Vertical
6) GRAMMAGE (G/ M.SQ.)
(OUTER TO INNER) : *250/150/150
7) BURST FACTOR OF PAPER
(KRAFT)
: 20.00
8) BURSTING STRENGTH OF
BOARD (KG/CM.SQ.) :
11.00
9) NO. OF PIECES PER
BOX : Not more than two
10) MANUFACTURER’S JOINT : By gluing
11) COMPRESSION STRENGTH
OF BOX (KGF) (MIN) : 300.00